MIRI II-12 Multiroom Incubator
$0.00
Shipped From Abroad
The Esco Medical MIRI® II-12 Multiroom Incubator is intended to be used to provide a stable culture environment at or near body temperature and CO2 and N2 gases for the development of gametes and embryos during In Vitro Fertilization (IVF) and Assisted Reproduction Technology (ART) treatments.
Typically 10-21 working days – excluding furniture and heavy/bulky equipment. Please contact us for further information.
Description
MIRI II-12 Multiroom Incubator
To ensure maximum performance and an environment with the least amount of stress for embryos, the Esco MIRI® II-12 Multiroom Incubator dedicates one chamber for each patient and has 24 completely separate PID temperature controllers.
The chambers are separate from one another and do not affect each other’s temperatures in any way. There is no effect on the remainder of the system from any disruption in one chamber, such as a temperature reduction after opening the lid. The temperature in the culture chambers and the lids can be controlled and regulated as well. The top and the bottom of each chamber are separated with a PET layer so that the lid temperature would not affect the bottom.
For validation purposes, each compartment has a PT-1000 sensor built in. The circuitry is separated from the unit’s electronics, so it remains a truly separate validation system.
The incubator needs 100% CO2 and 100% N2 to control the CO2 and O2 concentrations in the culture chambers. A dual-beam infra-red CO2 sensor with extremely low drift rates controls the CO2 levels. On the other hand, a chemical, medical-grade oxygen sensor controls the levels of O2 in the system.
CO2 recovery takes an average of 3 minutes after opening the lid.* The MIRI® II-12 incubator is fitted with 12 gas sample ports that allow the user to validate gas concentration by sampling gas from the individual compartment.
The incubator also features a recirculated gas system where gas is continuously put into the compartment and taken out at the same rate. Gas is cleaned via a 254 nm UVC light with direct gas contact between the bulb and gas. The UVC light has filters that inhibit any 185 nm radiation that would produce dangerous ozone. The filters are located under the UVC light. The complete gas repletion in the system takes less than 5 minutes.
- Pressure regulator (preventing dangerous gas pressure problems)
- Gas flow sensors (actual consumption can be accumulated)
- Gas pressure sensors (allow the user to know the pressure, and the variation can be logged to avoid dangerous conditions)
- Gas filters (to prevent valve problems)
Features
Heated Lid
Prevents condensation, enhances consistency throughout each chamber, and improves temperature regulation and recovery.
Heated Bottom
Allows for reliable temperature regulation by providing direct heat transfer to the culture dishes.
Fast Recovery
The quick recovery of temperature and gas characteristics after opening a chamber is a significant advantage when utilizing the MIRI® II-12 multiroom incubator.
Stress-free Validation of Chamber Parameters
For gas and temperature validation, the MIRI® II-12 can be connected to an external device such as the Esco MIRI® GA. The primary circuitry is fully separate from the built-in PT1000 temperature sensors. Additionally, all 6 or 12 chambers have gas sampling ports.
Intuitive Touchscreen Controls
User-Friendly and Full-Featured Data Logging System
One computer can control and connect to multiple machines. The machine’s real-time parameters can all be simply viewed in the MIRI® II-12’s built-in touchscreen PC. These parameters include every temperature and gas concentration point, as well as the set points for all gas input pressures and flow rates. Graphs are also available for viewing that show all machine performance information, including alerts, which are continuously documented. Weekly reports are also generated automatically by the data logger, making it more user-friendly.
Heating Optimization Plates
A heating optimization plate is included in each chamber to help heat transfer directly to the culture dishes. Each chamber contains inserts that suit different-sized dishes.
Specifications
| Overall dimensions (W x D x H) | 740 x 575 x 215 mm (29.1 x 22.6 x 8.5”) |
| Net Weight | 47 kg (99.2 lbs) |
| Material | Mild steel / Aluminum / PET / Stainless steel |
| Power supply | 115V 60Hz or 230V 50Hz |
| Power consumption | 500W |
| Temperature Control Range | 25.0 – 40.0 °C |
| *CO2 Gas Consumption | < 2 liters per hour |
| **N2 Gas Consumption | < 12 liters per hour |
| CO2 Control Range | 3.0% – 10.0% |
| O2 Control Range | 5.0% – 10.0% |
| Gas Input Pressure | 0.4 – 0.6 bar (5.80 – 8.70 PSI) |
| Operating Altitude | Up to 2000 meters (6560 feet or 80kPa – 106kPa) |
| Shipping weight | 57 kg (121.3 lbs) (Including the pallet’s weight) |
| Shipping dimension | 890 x 710 x 480 mm (35 x 28 x 18.9”) (device on the pallet) |
Quick Comparison
| MIRI II-12 Multiroom Incubator remove | Skyla Hi POC Clinical Chemistry Analyzer remove | IISM VPism-C (Compact Type) Vein Probe remove | ApexBio HemoSmart Gold Hemoglobin Meter remove | Discover 5 Panel Cup with Adulterants Per Pack remove | Sugentech Inclix (POCT) Immunoassay Analyzer remove | |||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Name | MIRI II-12 Multiroom Incubator remove | Skyla Hi POC Clinical Chemistry Analyzer remove | IISM VPism-C (Compact Type) Vein Probe remove | ApexBio HemoSmart Gold Hemoglobin Meter remove | Discover 5 Panel Cup with Adulterants Per Pack remove | Sugentech Inclix (POCT) Immunoassay Analyzer remove | ||||||||||||||||||||||||||||
| Image |  |  |  |  |  |  | ||||||||||||||||||||||||||||
| SKU | SF1033560060-2 | SF1033560090-1 | SF1033560084-29 | SF1033560084-23 | SF1033560084-89 | |||||||||||||||||||||||||||||
| Rating | ||||||||||||||||||||||||||||||||||
| Price |
|
|
| $55.00 |
|
| ||||||||||||||||||||||||||||
| Stock | ||||||||||||||||||||||||||||||||||
| Availability | ||||||||||||||||||||||||||||||||||
| Add to cart | ||||||||||||||||||||||||||||||||||
| Description | Shipped From Abroad
The Esco Medical MIRI® II-12 Multiroom Incubator is intended to be used to provide a stable culture environment at or near body temperature and CO2 and N2 gases for the development of gametes and embryos during In Vitro Fertilization (IVF) and Assisted Reproduction Technology (ART) treatments.
Delivery & Availability:
Typically 10-21 working days – excluding furniture and heavy/bulky equipment. Please contact us for further information.
| Shipped from Abroad The skyla Hi POC Clinical Chemistry Analyzer provides clinical testing laboratories of medical facilities and clinics with an in-vitro clinical chemistry diagnostic tool that is compact, portable, and reports rapid results.The use of skyla Hi in the management of diabetes enables better access to testing and rapid clinical decision making, discussion,and implementation of optimized treatment. Delivery & Availability: Typically 14 working days – excluding furniture and heavy/bulky equipment. Please contact us for further information. | Shipped from Abroad The iiSM VPism-C Vein Probe - Compact Unit is a compact, non-invasive infrared device to view blood vessels just beneath the skin. Includes a camera, touchscreen display, connector cable, power supply, camera stand, gooseneck arm, and instruction manual. Delivery & Availability: Typically 10 working days – excluding furniture and heavy/bulky equipment. Please contact us for further information. | In Stock
HemoSmart GOLD offers a fast and easy way to measure hemoglobin level and is the first biosensor-based palm sized hemoglobin testing system in the world.The one of its kind strip-based testing method offers ease of use and portability and requires only 1μL of blood.
Delivery & Availability: Typically 2 working days – excluding furniture and heavy/bulky equipment. Please contact us for further information. | In stock
The Discover Cup is an all-in-one drug of abuse test cup. The strips are self-contained and the entire cup is tamper resistant.
Delivery & Availability:
| In stock INCLIX™ is an immunochromatographic analyzer providing immediate point-of-care testing (POCT) at patient care settings or clinical laboratories. It facilitates automatic detection of various biomarkers for cardiovascular disease, infectious disease, cancer, diabetes, allergy, and etc. with high accuracy and sensitivity. INCLIX™ analyzer is a compact, easy-to-use and cost-effective multi-parameter POCT instrument and its unique user friendly software provides an efficient data management system. Delivery & Availability: Typically 5-7 working days – excluding furniture and heavy/bulky equipment. Please contact us for further information. | ||||||||||||||||||||||||||||
| Content | MIRI II-12 Multiroom IncubatorTo ensure maximum performance and an environment with the least amount of stress for embryos, the Esco MIRI® II-12 Multiroom Incubator dedicates one chamber for each patient and has 24 completely separate PID temperature controllers. The chambers are separate from one another and do not affect each other's temperatures in any way. There is no effect on the remainder of the system from any disruption in one chamber, such as a temperature reduction after opening the lid. The temperature in the culture chambers and the lids can be controlled and regulated as well. The top and the bottom of each chamber are separated with a PET layer so that the lid temperature would not affect the bottom. For validation purposes, each compartment has a PT-1000 sensor built in. The circuitry is separated from the unit's electronics, so it remains a truly separate validation system. The incubator needs 100% CO2 and 100% N2 to control the CO2 and O2 concentrations in the culture chambers. A dual-beam infra-red CO2 sensor with extremely low drift rates controls the CO2 levels. On the other hand, a chemical, medical-grade oxygen sensor controls the levels of O2 in the system. CO2 recovery takes an average of 3 minutes after opening the lid.* The MIRI® II-12 incubator is fitted with 12 gas sample ports that allow the user to validate gas concentration by sampling gas from the individual compartment. The incubator also features a recirculated gas system where gas is continuously put into the compartment and taken out at the same rate. Gas is cleaned via a 254 nm UVC light with direct gas contact between the bulb and gas. The UVC light has filters that inhibit any 185 nm radiation that would produce dangerous ozone. The filters are located under the UVC light. The complete gas repletion in the system takes less than 5 minutes.The high-performance CO2 and O2 sensors and built-in gas mixer enable precise adjustment of the gas phase composition and environment within the chambers.
Pure gas is used with the MIRI® II-12. Incubator steady-state gas conditions can be reached when 100% CO2 and N2 are used. This is crucial because it will maintain the pH during embryo development.
The incubator has a complete gas control system that consists of the following:
Petri dish location: Found in a compartment that is easy to reach and safe because of the compartment numbering and the ability to write on the white lid with a pen.
The software: It runs on the built-in touchscreen in the MIRI II-12 version. The software contains logging functions for long-term data logging and storage.
USB module: This enables the quality control data to be transferred for off-site evaluation. The performance of such allows the manufacturer to provide a valuable service to the customers.
A pH sensor port: The user can plug any standard BNC pH probe into the unit and measure the pH in the samples at will.
FeaturesHeated Lid Prevents condensation, enhances consistency throughout each chamber, and improves temperature regulation and recovery. Heated Bottom Allows for reliable temperature regulation by providing direct heat transfer to the culture dishes.Fast Recovery The quick recovery of temperature and gas characteristics after opening a chamber is a significant advantage when utilizing the MIRI® II-12 multiroom incubator. Stress-free Validation of Chamber Parameters For gas and temperature validation, the MIRI® II-12 can be connected to an external device such as the Esco MIRI® GA. The primary circuitry is fully separate from the built-in PT1000 temperature sensors. Additionally, all 6 or 12 chambers have gas sampling ports.Intuitive Touchscreen Controls Practitioners of IVF work with priceless, delicate, and sensitive embryos, and frequently, the smallest variables have a significant impact. The large touchscreen display on the MIRI® II-12 is used to concurrently control and monitor crucial parameters, such as temperature and gas concentration, and provide visual and audio alarms to indicate dangerous conditions, signify critical situations, and enable users to simultaneously manage and monitor key parameters (temperature, gas concentration, etc).
It boasts a sizable display that is clear from a distance, and because it is a PC, it is loaded with many capabilities to make life in the lab simpler. There is a possibility to connect an external monitor via an HDMI connector on the back of the unit to see the incubation parameters from a more significant distance. The glass lid tops may also be written on, which is a great organizational function.
User-Friendly and Full-Featured Data Logging System One computer can control and connect to multiple machines. The machine's real-time parameters can all be simply viewed in the MIRI® II-12’s built-in touchscreen PC. These parameters include every temperature and gas concentration point, as well as the set points for all gas input pressures and flow rates. Graphs are also available for viewing that show all machine performance information, including alerts, which are continuously documented. Weekly reports are also generated automatically by the data logger, making it more user-friendly. Heating Optimization Plates A heating optimization plate is included in each chamber to help heat transfer directly to the culture dishes. Each chamber contains inserts that suit different-sized dishes.Specifications
| skyla Hi Analyzer enables better access to testing and rapid clinical decision making, discussion, and implementation of optimized treatment. To get the result, only prepare <1 μl fingertips blood or venous blood (depends on test item) without pretreatment with easy steps and then read the result after 6 mins. The device allows two specimens be tested in one run and provides fully automatic procedures from checking the validity of cartridge to printing the results.
Reagent Kit
Main SpecificationPrinciple
Turbidimetric Method / Biochemistry
Device
Testing Time
5~20 minutes (depends on test items)
Display and Interface
5″ TFT color touch screen LCD
Memory Capacity
50,000 test results
Dimension of Analyzer
270 x 188 x 148 mm
Weight of Analyzer
1.7 kg
Dimension of Printer Module
134 x 100 x 82.7 mm
Weight of Printer Module
0.37 kg
Power Supply
100~240 volts AC, 50-60Hz
Data Transmission
USB 2.0*4 / USB 3.0*1 / RS232*1 / RJ45*1 / Wi-Fi (optional)
Reagent and SamplesSamples
Fingertips blood or venous blood
Samples Volume
0.8 ~ 30 μL (depends on test item)
Storage Temperature (Reagent)
2 ~ 8˚C
HumidityRelative humidity < 95% (Non-condensing)
| The iiSM VPism-C Vein Probe - Compact Unit is a compact, non-invasive infrared device to view blood vessels just beneath the skin. Includes a camera, touchscreen display, connector cable, power supply, camera stand, gooseneck arm, and instruction manual. This handheld, portable device is lightweight and includes the touchscreen and camera with attached clip. The camera can be removed and handled by hand, or can clip to the touchscreen unit for a hands-free experience. The back of the device also has a kickstand, so that physicians can stand the device on its own. The VPism-C can also be mounted to an armrest, if a patient needs to be stationary, or attached to a SLism-F Specialized Light Source for patients with deeper vessels. This device can be a vital tool in providing accurate placement of injections or other vascular treatments, such as for varicose veins. The infrared video shows the location of the veins and capillaries in real time, as well as save images for further discussion or diagnosis. For patients who have difficult-to-find veins, this device will save them from incorrect or painful injection sites.
Features:
Probe Target: Subcutaneous blood vessels of various patients (including capillaries)
Probe Method: Non-invasive infrared technology
Probe Depth: Within 10 mm under the skin
Magnification Function: Up to 1X, 2X and 4X
Automatic Adjustment Function: Adjusts the brightness automatically based on the targeted vein
Specialized Light Function: Shows the veins more clearly by using the specialized light source
Operation Method: Easy to operate with touchscreen
Internal Battery Support: Continuous running time: 1.5 hours
Warranty: 1 year
Click Here To Download Catalogue | HemoSmart GOLD offers a fast and easy way to measure hemoglobin level and is the first biosensor-based palm sized hemoglobin testing system in the world.The one of its kind strip-based testing method offers ease of use and portability and requires only 1μL of blood.
Feature
Click Here To Download Catalogue |
All-in-One Design
| INCLIX™ is an immunochromatographic analyzer providing immediate point-of-care testing (POCT) at patient care settings or clinical laboratories. It facilitates automatic detection of various biomarkers for cardiovascular disease, infectious disease, cancer, diabetes, allergy, and etc. with high accuracy and sensitivity. INCLIX™ analyzer is a compact, easy-to-use and cost-effective multi-parameter POCT instrument and its unique user friendly software provides an efficient data management system.
Features:
• Good accuracy owning to superior CMOS sensor & our own Algorism
• 10,000 test results data storage
• Instrument Check by Reference Kit
• Remote Support available (when connected via Internet)
• Built-in Thermal Printer and Barcode Scanner
• Data export to USB(PDF, Excel), Email and LIS
• Storage Temperature of Test Cassette & Buffer : Room temperature, 2 ~ 30 ℃
• Shelf Life of Test Cassette & Buffer : 24 months
Click Here To Download Catalogue | ||||||||||||||||||||||||||||
| Weight | N/A | N/A | N/A | N/A | N/A | N/A | ||||||||||||||||||||||||||||
| Dimensions | N/A | N/A | N/A | N/A | N/A | N/A | ||||||||||||||||||||||||||||
| Additional information |
|
Reviews
There are no reviews yet.